Laser |
The LaserProfile type exposes the following members.
Properties| Name | Description | |
|---|---|---|
 | EnableEquallySpacedPulses | Enables or disables generation of equally spaced laser pulses during scanner acceleration or deceleration. |
| EnableGateModulatesLm | Enable/Disable LM signal depending on gate. |
| EnableLaserSync | Enable/Disable the laser synchronization to a free-running laser. |
| EnablePointer | Enables the usage of the pointer. |
| EnablePowerCalibration | Enables or disables the use of the power calibration by way of a lookup table. |
| EnablePowerCorrection | Enables or disables the use of the position-dependent power correction. |
| EnableSecondaryPowerCalibration | Enables or disables the use of the power calibration for the secondary power target. |
| EnableSecondaryPowerCorrection | Enables or disables the use of the position-dependent power correction for the secondary power target. |
| EnableTickle | Enable/Disable the output of a tickle signal. |
| FpsPolarity | Polarity of the FPS output signal. |
| FpsStart | Time before marking when fps should be enabled. |
| FpsWidth | Width of the fps singal |
| GateHold | Gets or sets the Gate Hold time. |
| GatePolarity | Polarity of the Gate output signal. |
| GateSetup | Gets or sets the Gate Setup time. |
| HotPowerTarget | Gets or sets the target for the output. |
| LaserTriggerDelay | Gets or sets the laser trigger delay. |
| LMPolarity | Polarity of the LM output signal. |
| LmWidth | Width of the laser modulation signal. |
| LmWidthMode | Defines the mode of the laser modulation signal. |
| MaxDutyCycle | Maximum duty cycle. 1 is equivalent for maximum duty cycle. |
| MaxFrequency | Maximum value for validating laser frequency. |
| MaxPower | Maximum value for laser power. |
| MinFrequency | Minimum value for validating laser frequency. |
| MinPower | Minimum value for laser power. |
| NominalPower | |
| NominalSecondaryPower | |
| OffDelay | Defines an additional laser off delay, which is added to the one from the pen. |
| OnDelay | Defines an additional laser on delay, which is added to the one from the pen. |
| OpticalPulseWidthCount | The number of different optical pulse widths available in the laser. |
| OutputMode | Defines weather the LM signal is pulsed or continuous. |
| PowerCalibrationFile | Gets or sets the path of the power calibration file. Use EnablePowerCalibration for activation. |
| PowerChangeSetup | Gets or sets the amount of time the power is updated prior to the next laser event. |
| PowerCorrectionFile | Gets or sets the path of the power correction file. |
| PowerScale | Gets or sets the power scale factor. The resulting power scale will be multiplied with PowerScaleMultiplier. |
| PowerScaleMultiplier | Gets or sets the current power scale multiplier. The resulting power scale will be multiplied with PowerScale. |
| PowerWriteDelay | Gets or sets the delay between the power update and the assertion of the 'power write' signal. |
| PowerWriteWidth | Gets or sets the amount of time the 'power write' signal is asserted. |
| SecondaryPowerCalibrationFile | Gets or sets the path of the secondary power calibration file. Enable EnableSecondaryPowerCalibration for activation. |
| SecondaryPowerTarget | The output target for the secondary power, e.g. Simmer. |
| SimmerActivationDelay | Delay inserted after activating the simmer in case SimmerOnlyWhileMarking is true. |
| SimmerOnlyWhileMarking | When set to true, the simmer is only active during execution. |
| SimmerPowerTarget | The output target for the Simmer. |
| TickleFrequency | Frequency of the tickle. |
| TickleWidth | Width of the tickle. |
| ValidateMaxPowerChannelSum | |
| ValidationPowerUnit |
See Also